***** Guitar Project Jigs, Tools & Techniques Online Resources Archives OLF Video Page Library of plans MP3 Library Inlay Class
Offical Luthiers Forum





And our community proudly sponsored by:

RC Tonewoods | Stewart MacDonald | LuthiersForum
TasmanianTonewoods | OLF | OLF MERCH
Luthier Suppliers | Pacific Coast Woods | ELEVATE
OLF X | Tasmanian Acoustic Tonewood | Luthiers Forum Store!
Luthiers Forum | OLF Facebook | AVAIL SPACE
OLF | Alaska Specialty Woods | A.Hix Tonewood
Duke of Pearl | Birkonium CNC | Space




Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Jun 26, 2025 2:26 pm


Board index » Forum Archive

All times are UTC - 5 hours





Post new topic Reply to topic  Page 1 of 1
  [ 10 posts ] 
  Print view Previous topic | Next topic 
Author Message
Martin Turner
 Post subject:
PostPosted: Fri Jun 16, 2006 11:29 pm 
Offline
Koa
Koa

Joined: Sun Feb 26, 2006 10:21 pm
Posts: 1055
Location: Australia
Right chaps I have a bit of a dilema on my hands. Ive gone and fitted my
truss rod in upside down and I need to get the thing out and refit
correctly. The brass block at the heel end of the neck is epoxied into the
slot. Any ideas on undoing an epoxy joint would be appreciated. I have a
stock of spare truss rods so destroying the upside doen rod to extratc it
isnt an issue.

Cheers



Top
 Profile  
 
Pwoolson
 Post subject:
PostPosted: Fri Jun 16, 2006 11:33 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Sat Jan 08, 2005 1:26 am
Posts: 2558
Location: United States
Martin, epoxy lets go with heat. And it really doesn't take much. According to their spec team, West Systems creaps at 180? and let's go completely very soon after that. I'd consider a heat gun on low.


Top
 Profile  
 
Martin Turner
 Post subject:
PostPosted: Sat Jun 17, 2006 12:09 am 
Offline
Koa
Koa

Joined: Sun Feb 26, 2006 10:21 pm
Posts: 1055
Location: Australia
Thanks Paul. Will try a bit of heat and if that doesnt work Ill just have to
cut a bit of wood out.

Cheers


Top
 Profile  
 
old man
 Post subject:
PostPosted: Sat Jun 17, 2006 2:02 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Mon Jul 04, 2005 7:13 am
Posts: 3270
Location: United States
If you have a soldering iron or woodburning pen, you can apply heat right where you want it. That should do it.

Ron

_________________
OLD MAN formerly (and formally) known as:

Ron Wisdom

Somewhere in the middle of Arkansas......
Top
 Profile  
 
Louis Freilicher
 Post subject:
PostPosted: Sat Jun 17, 2006 4:09 am 
Offline
Cocobolo
Cocobolo
User avatar

Joined: Fri Mar 31, 2006 6:11 pm
Posts: 296
Location: United States
First name: Louis
Last Name: Freilicher
City: Belchertown
State: MA
Zip/Postal Code: 01007
Country: USA
Focus: Repair
Status: Professional
I have had very good luck removing inlays installed with super glue
or epoxy by heating the surface with a clothes iron until the fill turns
gooey, maybe 2-3 min, and prying the thin out with an exacto blade.   
The soldering iron will work too but takes a bit longer to reach the
right temp. The clothes iron will give you more even heat over the
whole surface. Good luck and work slow, I'm sure you can salvage
this neck.

Louis

_________________
- Louis Freilicher

Oh No! Not another learning experience!
Top
 Profile  
 
Billy T
 Post subject:
PostPosted: Sat Jun 17, 2006 7:41 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Sun Dec 25, 2005 7:58 pm
Posts: 2946
Location: United States
A little more gentle way, I heard about was using a flood light. Never done it though.

Billy Dean

_________________
Billy Dean Thomas
Covina, CA

"Multi famam, conscientiam, pauci verentur."
(Many fear their reputation, few their conscience)
Top
 Profile  
 
Martin Turner
 Post subject:
PostPosted: Sat Jun 17, 2006 11:44 am 
Offline
Koa
Koa

Joined: Sun Feb 26, 2006 10:21 pm
Posts: 1055
Location: Australia
Thanks for the replies guys.
Top
 Profile  
 
Michael Shaw
 Post subject:
PostPosted: Sat Jun 17, 2006 11:56 am 
Offline
Cocobolo
Cocobolo

Joined: Mon Apr 24, 2006 4:35 pm
Posts: 298
Location: United States
Heat the brass block with a 40 watt solder iron until the epoxy softens. That should loosen it up enough to work it out.
Top
 Profile  
 
Martin Turner
 Post subject:
PostPosted: Sat Jun 17, 2006 3:49 pm 
Offline
Koa
Koa

Joined: Sun Feb 26, 2006 10:21 pm
Posts: 1055
Location: Australia
Okay I got the heat gun on to the brass anchor block and hey presto after
2 minutes the epoxy went all crystally white. Got a pallette knife down
each side of the block and it came out.

Thanks again for the helpful suggestions

Martin
Top
 Profile  
 
Billy T
 Post subject:
PostPosted: Sat Jun 17, 2006 5:51 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Sun Dec 25, 2005 7:58 pm
Posts: 2946
Location: United States
Your welcome! Please come again!!

_________________
Billy Dean Thomas
Covina, CA

"Multi famam, conscientiam, pauci verentur."
(Many fear their reputation, few their conscience)
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 10 posts ] 

Board index » Forum Archive

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 5 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com